Energy, Power And Heating Effect
When current flows through a resistor, electrical energy is dissipated as heat — a phenomenon called Joule's heating effect. The rate of energy dissipation (power) is given by , and the total heat produced in time is joules. The maximum-power transfer theorem states that maximum power is delivered to a load when its resistance equals the source's internal resistance (). These formulas underpin electrical bill calculation, fuse ratings, and appliance design, and are core to the JEE Physics - Current Electricity and NEET Physics - Current Electricity syllabi.
- Electrical energy:
- Electrical power:
- Joule's heating: joule calorie
- Cell energy balance:
- Maximum power theorem: at , and
- Efficiency of a cell:
- Power rating of appliance:
- Bulbs in series: brighter bulb has higher ; bulbs in parallel: brighter bulb has lower
- Energy consumed (commercial): 1 kWh = J = 1 'unit' on electricity bill
1. Electrical Energy and Power
When a current flows for time through a device with potential difference across it, the charge that flows is and the energy delivered by the source is:
The rate of energy transfer (power) is:
For an ohmic resistor with :
SI units: energy in joule (J), power in watt (W) = J/s. Commercial unit of energy is kilowatt-hour (kWh):
2. Joule's Heating Effect
When current passes through a conductor, the drifting electrons collide with lattice ions and transfer kinetic energy to them. This raises the temperature of the conductor — the phenomenon is called Joule heating (or ohmic heating).
The heat produced in time is:
Or equivalently: . In calories: .
Laws of Joule Heating
- (at fixed and ).
- (at fixed and ) — only when current is fixed.
- (at fixed and ).
Important caveat: If voltage is fixed instead of current, then , so . In series (same ), a higher dissipates more heat. In parallel (same ), a lower dissipates more heat.
Applications of Joule Heating
- Electric heater, iron, geyser: nichrome coils with high resistivity dissipate large heat.
- Incandescent bulb: tungsten filament glows white-hot at ~2500 K.
- Fuse wire: tin-lead alloy with low melting point; melts and breaks the circuit if current exceeds rated value.
- Electric arc welding: intense heating at points of contact.
3. Energy Balance in a Circuit
Consider a cell of EMF and internal resistance connected to an external resistance . The current is . Multiplying by :
Interpretation:
- = rate at which chemical energy is converted to electrical energy inside the cell.
- = power delivered to (dissipated in) the external load.
- = power dissipated inside the cell (heats the cell).
Efficiency of the cell (fraction of energy delivered to load):
4. Maximum Power Transfer Theorem
For a given cell (fixed , ), what value of external resistance absorbs the maximum power?
Power delivered to :
To maximise, set :
The power output is maximum when the external resistance equals the internal resistance.
Substituting back:
Efficiency at maximum power transfer:
At , power delivered to the load is maximum but only half the total power reaches the load — the other half is wasted heating the cell. For efficient power transmission (e.g. grid), we want so efficiency approaches 100%, even though absolute delivered power is smaller. Maximum power theorem is useful for matching audio impedance and low-power sensors, not for power generation.
5. Bulbs in Series vs Parallel
Consider two bulbs with power ratings and at rated voltage . Their resistances are:
Lower power rating means higher resistance (for the same voltage rating).
Series Connection (same current)
With both bulbs in series across supply , current is common. Actual power dissipated in each: . Since is inversely proportional to rated power:
In series, the bulb with the lower power rating glows brighter (because it has higher resistance).
Parallel Connection (same voltage)
With both bulbs in parallel across supply : . Directly:
In parallel, the bulb with the higher power rating glows brighter (household wiring uses parallel so each appliance runs at rated brightness).
Q: A copper wire has cross-section mm and length m, initially at C, thermally insulated. A current of A is set up. (a) Find the time in which the wire starts melting. (b) What if the length is doubled?
Given: density of Cu kg/m, specific heat cal/(kg C) J/cal, melting point C, resistivity m. Neglect temperature variation of .
Solution(a) Mass of wire:
Temperature rise: C.
Specific heat: J/(kgC).
Resistance:
Setting heat produced equal to heat required to melt:
(b) If length is doubled: doubles, but so does . The ratio (which appears when substituting into the formula) leaves unchanged. Wire melts in the same time.
Q: A 100 W, 220 V bulb and a 60 W, 220 V bulb are connected (a) in series across 220 V, (b) in parallel across 220 V. In each case, which bulb glows brighter?
SolutionResistances: , .
(a) Series: total , current A.
The 60 W bulb glows brighter in series (higher ).
(b) Parallel: each bulb sees full 220 V, so each dissipates its rated power. The 100 W bulb glows brighter (higher rated power).
Q: An electric geyser rated 2000 W, 220 V is used for 30 minutes daily. If electricity costs ₹8 per unit (kWh), find the monthly (30-day) cost of running the geyser.
SolutionDaily energy: .
Monthly energy: kWh = 30 units.
Cost: 30 \times 8 = \rupee\,240 per month.
A fuse is a thin wire with low melting point (tin-lead alloy) placed in series with the load. Its cross-section is chosen so that Joule heating melts it once current exceeds the safe rated value. Since heat produced per unit length , and heat loss depends on surface area, the fuse rating scales as where is diameter.